Carbon skinning final sand problem !!


Carbon skinning final sand problem !!
View
Options
Author
Message
Lillee
L
Lillee
posted 6 Years Ago HOT
Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)
Group: Forum Members
Posts: 5, Visits: 25
Hey so if done some bike panels in carbon skinning the process went really well right up till final sand with 400 grit the panels have started to peel almost like orange peel on the resin, I'm now completely stuck on how to progress forward 
Reply Like 3
Reply
Lillee
L
Lillee
posted 6 Years Ago HOT
Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)Forum Member (36 reputation)
Group: Forum Members
Posts: 5, Visits: 25
 
CmCarbon - 4/3/2019 10:14:52 AM
Try pic of any loose resin and sand it back.. then reapply another few coats of resin

Thank you very  much I wil 're try 
Reply Like 3
GO

Merge Selected

Merge into selected topic...



Merge into merge target...



Merge into a specific topic ID...



Submit

Threaded View
Threaded View
Carbon skinning final sand problem !!
Lillee - 6 Years Ago
     Looks like you've applyed resin after the tackyness has gone so it hasn't bonded to the previous resin coat. Xcr resin by any chance?
CmCarbon - 6 Years Ago
             I think I missed it by half hour, silly me for applying it, yes its xcr, I don't no we're to go from here?
Lillee - 6 Years Ago
     Try pic of any loose resin and sand it back.. then reapply another few coats of resin
CmCarbon - 6 Years Ago
             Thank you very much I wil 're try
Lillee - 6 Years Ago
     when you wet it out with just a bit of water, do you still see the marks? if not you are ok to apply next layers on top. It is probably where you've sanded through different coats
matthieutje65 - 6 Years Ago
             When wiped with a wet micro fibre you still can see the marks, what would you advise next??
Lillee - 6 Years Ago
     Wipe it with acetone, I hated xcr resin.. it does this all the time and why I stopped using it
CmCarbon - 6 Years Ago
     Aww really what product is better that doesn't do this and thank you I will apply some
Lillee - 6 Years Ago
     If your skinning I just use surf board poly resin. .crystal clear, higher temp rating.easy sandandcuresin 10mins if it's warm . final coat adds me wax additive and seals and cures so it can be sanded
CmCarbon - 6 Years Ago
             I personally think the XCR resin is an excellent product for skinning pieces. I don't skin that much pieces because I prefer using moulds and resin infusion or prepreg, but when skinning pieces XCR i...
matthieutje65 - 6 Years Ago
     I like how it flows, self levels and bubble free, I always had issues same as this post.. I only used the resin on s work bench with heat lamps which kept the temp around 30 degrees, resin was always...
CmCarbon - 6 Years Ago
             If you need to use heat lamps on top of your part isn't mostly a good sign :D in best conditions you have your part in a room with very low humidity and constant temperatures (part and resin) at...
matthieutje65 - 6 Years Ago

Similar Topics

Post Quoted Reply
Reading This Topic

Powered by InstantForum 2017-0 Final © 2025
Execution: 0.000. 1 query. Compression Enabled.
Explore
Messages
Mentions
Search