Help

Talk Composites - The Forum for Advanced Composites

Back

Help

Author	Message
111mattin111	111mattin111 posted 10 Years Ago HOT Topic Details
Group: Forum Members Posts: 67, Visits: 910	OK need a little help I've done a quick video as well to show what im on about I've vaccum bagged my lay up and got absolute vaccum, but when I do a drop test leaving it 15min when I come back to it turn the pump on and release the clamp it starts pulling vaccum again then after a few minutes it pulls absolute vaccum again without touching anything, Is this normal or is something causing it to do this? I don't want to infuse it if airs getting into the bag Thanks Paul
	Reply Like 3

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Help

111mattin111 - 10 Years Ago

http://s200.photobucket.com/user/rb200/library/?view=recent&page=1

111mattin111 - 10 Years Ago

Well been over the bag a million times and can't find the leak, I can get it to pull vaccum but once...

111mattin111 - 10 Years Ago

Hi Good housekeeping helps regarding leaking bags so make sure you bagging material is stored in a...

carbonfibreworks - 10 Years Ago

The vac bag has been stored it a sealed bag out of the way, Would it still be able to pull full vac...

111mattin111 - 10 Years Ago

Hi One way to check it is envelope bag the mould but make sure the back of the mould has been sanded...

carbonfibreworks - 10 Years Ago

Not sure I'd be able to envelope bag it due to the size and weight of the mould, Hmmmm not really...

111mattin111 - 10 Years Ago

Hi Just try re bagging first. Regards Chris

carbonfibreworks - 10 Years Ago

Ive found most leaks are around the tape and especially at the vacuum intake and outlet at the bag...

VVS - 10 Years Ago

to answer your question if you do not have a digital vacuumreader you can get "full" vacuum on the...

matthieutje65 - 10 Years Ago

Ok so sorted the leak out and no pressure drop after couple of hours then the nightmare started...

111mattin111 - 10 Years Ago

Just ironing out the kinks mate, happens to everyone when they first start infusing. Keep at it,...

Hanaldo - 10 Years Ago

I used the hose that comes with the infusion starter kit, which other hose would you recommend?

111mattin111 - 10 Years Ago

I see. Well in that case, I'd probably get in contact with the guys at EC, as their stuff definitely...

Hanaldo - 10 Years Ago

I thought that, I now think it was definitely down to collapsed pipes as soon as I changed them it...

111mattin111 - 10 Years Ago

I have used the EC clear hose many times and the only time it has collapsed is when its been too...

carbonfibreworks - 10 Years Ago

I mixed the resin with slow hardner, I didn't have any blow heaters on it was done in the house, the...

111mattin111 - 10 Years Ago

OK so that's a slightly different issue and can happen with this type of hose, when you have started...

carbonfibreworks - 10 Years Ago

I did try that putting the clamp back on and trying to squash the pipe back the other way, I think...

111mattin111 - 10 Years Ago

Was your resin feed pot positioned below the part? If it was higher the liquid resin could siphon...

Frobisher - 10 Years Ago

Yes the pot was slightly higher than part so would explain the puddle of resin, does everyone else...

111mattin111 - 10 Years Ago

I've had a few instances of the clear EC pipe squashing flat under vacuum .. :( It usually happens...

Dravis - 10 Years Ago

Great tip thanks for that I'll try this next time

111mattin111 - 10 Years Ago

Paul, Can you highlight where you store your resin and hardner and at what temperature they are...

Superleggera - 10 Years Ago

There stored in my workshop which does get cold at night is this no good? Before I mixed they were...

111mattin111 - 10 Years Ago

Paul, I keep my IN2 and AT30 stored at about 25 degrees and it lowers the viscosity significantly....

Superleggera - 10 Years Ago

Just to add to the previous points - I've found that, nearly all the time, leaks haveactually...

MarkMK - 10 Years Ago

As far as I've read this topic, one question hasn't been asked...Do you infuse on top of the...

matthieutje65 - 10 Years Ago

[quote][b]111mattin111 (01/11/2015)[/b][hr] OK need a little help I've done a quick video as well...

fgayford - 10 Years Ago

Thanks for the advice and replies not had chance to do my second lay up yet but will be doing one...

111mattin111 - 10 Years Ago

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google

Help

Help

Merge Selected

Threaded View

Similar Topics

Reading This Topic

Login

Explore

Messages

Mentions

Search