Final resin coats


Final resin coats
View
Options
Author
Message
easby
easby
easby
posted 8 Years Ago HOT
Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)
Group: Forum Members
Posts: 6, Visits: 44
Hi, can anyone give advice on what is causing these air like bubbles are? any info would help. Thanks 
Reply Like 5
Replies
Warren (Staff)
Warren (Staff)
Warren (Staff)
posted 8 Years Ago HOT
Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)Supreme Being (22K reputation)
Group: Administrators
Posts: 2.5K, Visits: 8.5K
It's hard to see in that photo.  Have you got any thing close up?


Warren Penalver
Easy Composites / Carbon Mods - Technical Support Assistant
Reply Like 4
easby
easby
easby
posted 8 Years Ago HOT
Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)Forum Guru (63 reputation)
Group: Forum Members
Posts: 6, Visits: 44
 
Warren (Staff) - 12/5/2017 3:05:24 PM
It's hard to see in that photo.  Have you got any thing close up?



Not sure if this is any better??
They look like air bubbles but do not go with heat
Thanks
Reply Like 5
GO

Merge Selected

Merge into selected topic...



Merge into merge target...



Merge into a specific topic ID...



Submit

Threaded View
Threaded View
Final resin coats
easby - 8 Years Ago
     It's hard to see in that photo. Have you got any thing close up?
Warren (Staff) - 8 Years Ago
             Not sure if this is any better?? They look like air bubbles but do not go with heat Thanks
easby - 8 Years Ago
     it could either be dust in the resin or perhaps more likely, the surface effect of pinholes or small surface voids on lower layers of resin (presume this is skinning?).
Warren (Staff) - 8 Years Ago
             I did panel wipe parts down 1st. Also if I even if i put another layer down still get them? could it be contamination with the resins? temp is around 18 degree
easby - 8 Years Ago
     It could in theory be some kind of contamination in a resin but unlikely the way most resins are made and bottled. Could be as simple as bits in the air landing on it during the cure. Does sanding....
Warren (Staff) - 8 Years Ago
             yes sanding does remove but effectively takes it back to the layer we just put on. Main issue is once part is prepped and ready for 2k lacquer we get the same effect once lacquer goes on. Only real.....
easby - 8 Years Ago
     Epoxy resins are prone to pinholes which is what that looks like.. if your laquaring I put the first coat on and use a brush on the pinholes, just put a heavy coat on and brush the pinholes, it shoul...
Interloper393 - 8 Years Ago
     If it is definitely pin holes then as described above, you can literally fill them before lacquering. Brushing into the pinholes is the way. You need the pinholes to fill up with lacquer before you.....
Warren (Staff) - 8 Years Ago

Similar Topics

Post Quoted Reply
Reading This Topic

Powered by InstantForum 2017-0 Final © 2025
Execution: 0.000. 2 queries. Compression Enabled.
Explore
Messages
Mentions
Search