Carbon Tub for Noble

Talk Composites - The Forum for Advanced Composites

Back

Home
»
Advanced Composites Forum
»
Projects
»
Motorsport, Vehicle Design and Modification
»
Carbon Tub for Noble

Carbon Tub for Noble

Author	Message
andygtt	andygtt posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 157, Visits: 1.2K	Been slowly working through the rest of the mould... its turned out to be an 8 part mould, just the custard to go on the rear window section then I can release it. strangely I'm pretty excited about breaking the mould off the buck. wheel arches have been a nightmare to do, these extend under the sills and I've really struggled to get the custard coat to stick under the return. Gel coat on rear window section (last part ) Coupling coat on the rear window section... custard will follow in 2014
	Reply Like 2
FLD	FLD posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 468, Visits: 2.7K	Warren (Staff) (18/12/2013) Looking good Andy!! FLD - I will do my own thread in due course once i have something to show!! Bit snowed down with other stuff and other cars breaking down at the minute! I'll look forward to it. I've just done a hard top for my car that weighs less than the soft top! I'll have a few pics up soon(ish)
	Reply Like 3
Warren (Staff)	Warren (Staff) posted 12 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Looking good Andy!! FLD - I will do my own thread in due course once i have something to show!! Bit snowed down with other stuff and other cars breaking down at the minute! Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 3
andygtt	andygtt posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 157, Visits: 1.2K	next step was to go over the 2 coats of Gel with a thin coupling coat using glass tissue... this allows the custard coat to bond to the Gel coat as they use a different chemical composition. The custard coat layer is put on very resin rich, its contains a material that expands at the same rate as the resin in it shrinks which means it has effectively zero shrinkage... all my moulds so far have been absolute exact copies of my buck's which means the final parts fit together perfectly with great shut lines. One issue I have noticed this morning that that I have managed to do a few drips on the rest of the exposed body, and when removed these have reacted slightly with the paint, so I am going to have to do a little remedial work to resolve before making the other mould sections. Here are the pics of the custard coat.
	Reply Like 3
FLD	FLD posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 468, Visits: 2.7K	Warren (Staff) (16/12/2013) Not thinking of cutting out the space frame and making a semi-monocoque centre tub in carbon then?? Im going the whole hog with my project but it will take a while!! Care to elaborate?
	Reply Like 2
Warren (Staff)	Warren (Staff) posted 12 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Not thinking of cutting out the space frame and making a semi-monocoque centre tub in carbon then?? Im going the whole hog with my project but it will take a while!! Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 3
andygtt	andygtt posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 157, Visits: 1.2K	Its a space frame so the tub isn't structural... Once I have removed the original tub I am going to replace all the alloy panels with carbon ones
	Reply Like 3
Warren (Staff)	Warren (Staff) posted 12 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Looking good Andy!! Under the fibreglass tub is there a metal spaceframe or is it a true structural composite centre tub on nobles?? Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 3
andygtt	andygtt posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 157, Visits: 1.2K	I started making the barriers for the first mould section.... Care must be taken to ensure the mould will release from both the buck AND the final part. You will always make the final part slightly oversize so it's very easy to accidentally get a lock on the overlap or the other mould sections. Current plan is for this to be 9 sections ( my rear clip was 12).... So far I have got the first layer of the gel coat down, another coat tomorrow morning and then I can do the coupling coat.
	Reply Like 3
andygtt	andygtt posted 12 Years Ago HOT Post Details
Group: Forum Members Posts: 157, Visits: 1.2K	pk_090 (12/12/2013) Haven't posted on this forum in a loooooon time but i think this is really worthy. I love what you are doing here Andy! What engine specs are you going for? Also just to add this spanner to the works, a friend of mine works for the company that provides f1 teams with their pre-preg. He told me that red bull racing cam covers were 1 layer thick of normal pre-preg carbon. Obviously i can say this is 100% accurate but i can see why they do it! Alex glad you like it, and thanks for the info... the engine is already 700bhp, its unique in the UK as its a single turbo that I designed myself with my own design of clutch package.... car is a real 1off in almost all areas. To be honest all the mods on this car is simply R&D for my scratch build car that I have designed and been building forever lol.
	Reply Like 3