Looking for help and info pls

Talk Composites - The Forum for Advanced Composites

Back

Looking for help and info pls

Author	Message
Coxo	Coxo posted 8 Years Ago HOT Topic Details
Group: Forum Members Posts: 39, Visits: 476	Hi I am looking for help and some info to see where I went Wrong I made a mould and when I pulled it out it looked like this Attachments IMG_4524.JPG (581 views, 2.00 MB)
	Reply Like 3
Replies
Fasta	Fasta posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 468, Visits: 3.5K	If I were laying this part up in any process I would cut small clean rectangles to cover the vent sections only and then cut two larger longer lengths and lay this on each long side overlapping the whole centre vent sections. Clean joins are not very noticeable and usually much less noticeable than distorted weave. I can't see how you can get a leak on such a simple bag. Full envelope bag? Tape each end. Fastacraft Facebook page
	Reply Like 3
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	Yeh fasta full envelope bag tape on each end
	Reply Like 3

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Looking for help and info pls

Coxo - 8 Years Ago

Loads of bridging and potentially a bit of a mould stick too.

Hanaldo - 8 Years Ago

I would agree. It is a difficult part to do initially. The key is getting the air out and also the...

Warren (Staff) - 8 Years Ago

You need to cut the fabric into smaller pieces and as above make sure the material is placed into...

scottracing - 8 Years Ago

I sorry I forgot to say i wetted out the mould then hand layed the carbon and wet the carbon too...

Coxo - 8 Years Ago

Did you coat the mould and then leave the resin to firm up for 2 or 3 hours? That first coat of...

Hanaldo - 8 Years Ago

Ok got use. Now I weted it out and applied the carbon straight way put in to rough position Then...

Coxo - 8 Years Ago

As Scott said, cutting the fabric into smaller pieces with the aid of some small templates, will...

MarkMK - 8 Years Ago

What do u mean by cutting into smaller peices Would that be on the second layer and so on ?

Coxo - 8 Years Ago

[quote][b]Coxo (12/01/2017)[/b][hr]What do u mean by cutting into smaller pieces Would that be on...

MarkMK - 8 Years Ago

What do u mean by cutting into smaller peices Would that be on the second layer and so on ?

Coxo - 8 Years Ago

That's a really difficult shape for doing what you are trying. Probably best done with infusion or...

Fasta - 8 Years Ago

I have tryed here as per above post waiting till tack I'll see how that gose or infusion as u say...

Coxo - 8 Years Ago

You need to cut the pieces smaller so that they sit into the tight rads. When you do wet lay like...

scottracing - 8 Years Ago

Nearly got it talk a. About a had part to do

Coxo - 8 Years Ago

Hopefully I can get it Thanks

Coxo - 8 Years Ago

The problem I am getting really is full vacuum I can here a leak but no matter what I can't seem to...

Coxo - 8 Years Ago

You will be better cutting strips with a 45degree orientation and laying them into the rads then...

scottracing - 8 Years Ago

If I were laying this part up in any process I would cut small clean rectangles to cover the vent...

Fasta - 8 Years Ago

Yeh fasta full envelope bag tape on each end

Coxo - 8 Years Ago

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google