Looking for help and info pls

Talk Composites - The Forum for Advanced Composites

Back

Looking for help and info pls

Author	Message
Coxo	Coxo posted 8 Years Ago HOT Topic Details
Group: Forum Members Posts: 39, Visits: 476	Hi I am looking for help and some info to see where I went Wrong I made a mould and when I pulled it out it looked like this Attachments IMG_4524.JPG (585 views, 2.00 MB)
	Reply Like 3
Replies
Fasta	Fasta posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 468, Visits: 3.5K	That's a really difficult shape for doing what you are trying. Probably best done with infusion or pre pregs rather than "wet bagging". Fastacraft Facebook page
	Reply Like 2
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	I have tryed here as per above post waiting till tack I'll see how that gose or infusion as u say fasta But I am not sure how to do that Attachments IMG_4529.JPG (338 views, 726.00 KB)
	Reply Like 3

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Looking for help and info pls

Coxo - 8 Years Ago

Loads of bridging and potentially a bit of a mould stick too.

Hanaldo - 8 Years Ago

I would agree. It is a difficult part to do initially. The key is getting the air out and also the...

Warren (Staff) - 8 Years Ago

You need to cut the fabric into smaller pieces and as above make sure the material is placed into...

scottracing - 8 Years Ago

I sorry I forgot to say i wetted out the mould then hand layed the carbon and wet the carbon too...

Coxo - 8 Years Ago

Did you coat the mould and then leave the resin to firm up for 2 or 3 hours? That first coat of...

Hanaldo - 8 Years Ago

Ok got use. Now I weted it out and applied the carbon straight way put in to rough position Then...

Coxo - 8 Years Ago

As Scott said, cutting the fabric into smaller pieces with the aid of some small templates, will...

MarkMK - 8 Years Ago

What do u mean by cutting into smaller peices Would that be on the second layer and so on ?

Coxo - 8 Years Ago

[quote][b]Coxo (12/01/2017)[/b][hr]What do u mean by cutting into smaller pieces Would that be on...

MarkMK - 8 Years Ago

What do u mean by cutting into smaller peices Would that be on the second layer and so on ?

Coxo - 8 Years Ago

That's a really difficult shape for doing what you are trying. Probably best done with infusion or...

Fasta - 8 Years Ago

I have tryed here as per above post waiting till tack I'll see how that gose or infusion as u say...

Coxo - 8 Years Ago

You need to cut the pieces smaller so that they sit into the tight rads. When you do wet lay like...

scottracing - 8 Years Ago

Nearly got it talk a. About a had part to do

Coxo - 8 Years Ago

Hopefully I can get it Thanks

Coxo - 8 Years Ago

The problem I am getting really is full vacuum I can here a leak but no matter what I can't seem to...

Coxo - 8 Years Ago

You will be better cutting strips with a 45degree orientation and laying them into the rads then...

scottracing - 8 Years Ago

If I were laying this part up in any process I would cut small clean rectangles to cover the vent...

Fasta - 8 Years Ago

Yeh fasta full envelope bag tape on each end

Coxo - 8 Years Ago

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google