Cut and lay carbon fabric

Talk Composites - The Forum for Advanced Composites

Back

Cut and lay carbon fabric

Cut and lay carbon fabric

Author	Message
Massimiliano	M Massimiliano posted 5 Years Ago HOT Topic Details
M Group: Forum Members Posts: 167, Visits: 1.1K	Hi, I would like to infuse the attached mold with carbon fiber, several layers of 380 gsm 12k twill carbon. What is the best way to cut the fabric and place in the mold, also to avoid tows separation at the edges?
	Reply Like 4
Reply
Massimiliano	M Massimiliano posted 4 Years Ago HOT Post Details
M Group: Forum Members Posts: 167, Visits: 1.1K	+x oekmont - 1/7/2021 8:40:04 AM For large infusions, I take a strip of flow mesh an stitch it to an omega like shape around the spiral feed tube. With that technique the spiral tube can be set off from the part, and leaves no traces at the part at all. Dd compound sells a product like this if you need further clarification. Thank you for the hint! For the DD compound product, you mean Blade runner ?
	Reply Like 3

GO

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Threaded View

Cut and lay carbon fabric

mporta71 - 5 Years Ago

Just give it a go man, you'll quickly learn what the material can and can't do. Start with the first layer and take your time, if you mess it up visually then just use that layer as one of the backin...

Hanaldo - 5 Years Ago

Thank you! I was thinking of making a shape of the internal of the mold with paper and then cut the fabric to shape a little oversized and trim in the mold... good idea or bad idea?

mporta71 - 5 Years Ago

Good idea if it works, bad idea if it doesn't haha. Just give things a try man. I suspect it will be difficult to do like that though, it is a complex shape and the dry fabric is going to move around...

Hanaldo - 5 Years Ago

... going to send the mold to Australia soon! 😅😄

mporta71 - 5 Years Ago

So I did it and I am not dissatisfied with the result. I have given a try to the MTI hose and very happy with it, but the resin inlet spiral left a bad print on the part: seems like the carbon under....

mporta71 - 4 Years Ago

Make sure you have enough bag above the spiral hose, then once the infusion is finished you pull the hose up into the fold of the vacuum bag. Either that or infuse from side to side if the geometry.....

SleepingAwake - 4 Years Ago

Thank you! I will try the fold suggestion as mti videos suggest to place the mti hose all around the part (see the white line in my pic) and place the resin inlet in the middle.

mporta71 - 4 Years Ago

It's much better and much easier to just keep all the hoses off the part. Infusing from the centre is a good idea for larger parts, but for small parts it is really unnecessary and can cause you...

Hanaldo - 4 Years Ago

While i agree with you and would do the same, for a beginner it would be safer with the inlet in the centre. With a little bit of bridging the racetracking on such a geometry can ruin your part when....

SleepingAwake - 4 Years Ago

It's nearly 1.5 meters x 0.80.

mporta71 - 4 Years Ago

Run the feed spiral up one side and the mti up the other.

Hanaldo - 4 Years Ago

Thank you. I did like you suggest with the other infusions but this one has 600 € of carbon in it and I am very worried of a mistake leading to a bad part, so I would prefer to waste some MTI but be....

mporta71 - 4 Years Ago

For large infusions, I take a strip of flow mesh an stitch it to an omega like shape around the spiral feed tube. With that technique the spiral tube can be set off from the part, and leaves no trace...

oekmont - 4 Years Ago

Thank you for the hint! For the DD compound product, you mean Blade runner ?

mporta71 - 4 Years Ago

Similar Topics

Post Quoted Reply

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google

Explore

Messages

Mentions

Search