Fixing bubbles in cured resin

Talk Composites - The Forum for Advanced Composites

Back

Fixing bubbles in cured resin

Author	Message
Peter Czaga	Peter Czaga posted 6 Years Ago HOT Topic Details
Group: Forum Members Posts: 2, Visits: 12	I would like to ask some tips how to fix bubbles in a completely cured resin? Unfortunately some bubbles has showed up at the end of the first stage so i couldn't fix it at that moment because it was partially cured. After the finish of the second stage and cured completely, i have drilled some test holes into an off-cut piece to check what's going to happen when i filled it with resin again. I cleaned the holes with white spirit and vacuum cleaner so the holes were fully clean. But i am not really satisfied with the results. Is there any way to fix those bubbles? I attached 2 pictures (bubbles and test holes) I have used Glasscast 50
	Reply Like 9
Replies
Warren (Staff)	Warren (Staff) posted 6 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 5
pootrain	p pootrain posted 6 Years Ago HOT Post Details
p Group: Forum Members Posts: 3, Visits: 17	+x Warren (Staff) - 5/20/2019 4:33:42 PM It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Is this my best bet for something like this? Got a bit over zealous with a heat gun and kind of cooked the resin as bubbles were coming out from under the caps.
	Reply Like 5
*Tom (Staff)*	T *Tom (Staff)* posted 6 Years Ago HOT Post Details
T Group: Moderators Posts: 21, Visits: 977	+x pootrain - 9/9/2019 7:56:09 AM +x Warren (Staff) - 5/20/2019 4:33:42 PM It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Is this my best bet for something like this? Got a bit over zealous with a heat gun and kind of cooked the resin as bubbles were coming out from under the caps. Good Morning, Thank you for getting in contact. It seems as though all of the bubbles are on the surface of the resin. To repair this, you will need to completely sand the surface until all marks have been removed and then you could either pour a new layer of GlassCast 3 or move up the grits of sand paper and then finish with a polish. If you are working in a room that is 20'c, it is not necessary to go over the resin with a heat gun as it is completely self degassing. However, if you are going to use a heat gun, you have to go over the surface very quickly trying not to over heat the resin. I hope this helps.
	Reply Like 6
pootrain	p pootrain posted 6 Years Ago HOT Post Details
p Group: Forum Members Posts: 3, Visits: 17	+x Tom (Staff) - 9/9/2019 9:07:54 AM +x pootrain - 9/9/2019 7:56:09 AM +x Warren (Staff) - 5/20/2019 4:33:42 PM It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Is this my best bet for something like this? Got a bit over zealous with a heat gun and kind of cooked the resin as bubbles were coming out from under the caps. Good Morning, Thank you for getting in contact. It seems as though all of the bubbles are on the surface of the resin. To repair this, you will need to completely sand the surface until all marks have been removed and then you could either pour a new layer of GlassCast 3 or move up the grits of sand paper and then finish with a polish. If you are working in a room that is 20'c, it is not necessary to go over the resin with a heat gun as it is completely self degassing. However, if you are going to use a heat gun, you have to go over the surface very quickly trying not to over heat the resin. I hope this helps. Thanks for the reply. Unfortunately a few of the bubbles actually go all the way down to the surface of the table and between the caps so sanding would not be very feasible. Would drilling down into them and then sanding the surface left exposed work? Forgot to say I am planning on pouring another layer anyway to achieve the depth I want. Edited 6 Years Ago by pootrain
	Reply Like 6
*Tom (Staff)*	T *Tom (Staff)* posted 6 Years Ago HOT Post Details
T Group: Moderators Posts: 21, Visits: 977	+x pootrain - 9/9/2019 10:18:26 AM +x Tom (Staff) - 9/9/2019 9:07:54 AM +x pootrain - 9/9/2019 7:56:09 AM +x Warren (Staff) - 5/20/2019 4:33:42 PM It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Is this my best bet for something like this? Got a bit over zealous with a heat gun and kind of cooked the resin as bubbles were coming out from under the caps. Good Morning, Thank you for getting in contact. It seems as though all of the bubbles are on the surface of the resin. To repair this, you will need to completely sand the surface until all marks have been removed and then you could either pour a new layer of GlassCast 3 or move up the grits of sand paper and then finish with a polish. If you are working in a room that is 20'c, it is not necessary to go over the resin with a heat gun as it is completely self degassing. However, if you are going to use a heat gun, you have to go over the surface very quickly trying not to over heat the resin. I hope this helps. Thanks for the reply. Unfortunately a few of the bubbles actually go all the way down to the surface of the table and between the caps so sanding would not be very feasible. Would drilling down into them and then sanding the surface left exposed work? Forgot to say I am planning on pouring another layer anyway to achieve the depth I want. Thank you for getting back to me. Unfortunately you will need to drill down into the resin and pour more in to fill the gaps. I am sorry I don't have better news for you.
	Reply Like 5
pootrain	p pootrain posted 6 Years Ago HOT Post Details
p Group: Forum Members Posts: 3, Visits: 17	+x Tom (Staff) - 9/9/2019 10:30:03 AM +x pootrain - 9/9/2019 10:18:26 AM +x Tom (Staff) - 9/9/2019 9:07:54 AM +x pootrain - 9/9/2019 7:56:09 AM +x Warren (Staff) - 5/20/2019 4:33:42 PM It should still fill the holes fine. However its the slight refraction between the two layers - the fresher the resin, the more cross linking will occur with the new pour. After a week or so, You may not get it to look much better. Is this my best bet for something like this? Got a bit over zealous with a heat gun and kind of cooked the resin as bubbles were coming out from under the caps. Good Morning, Thank you for getting in contact. It seems as though all of the bubbles are on the surface of the resin. To repair this, you will need to completely sand the surface until all marks have been removed and then you could either pour a new layer of GlassCast 3 or move up the grits of sand paper and then finish with a polish. If you are working in a room that is 20'c, it is not necessary to go over the resin with a heat gun as it is completely self degassing. However, if you are going to use a heat gun, you have to go over the surface very quickly trying not to over heat the resin. I hope this helps. Thanks for the reply. Unfortunately a few of the bubbles actually go all the way down to the surface of the table and between the caps so sanding would not be very feasible. Would drilling down into them and then sanding the surface left exposed work? Forgot to say I am planning on pouring another layer anyway to achieve the depth I want. Thank you for getting back to me. Unfortunately you will need to drill down into the resin and pour more in to fill the gaps. I am sorry I don't have better news for you. Thats fine. Thank you for your help.
	Reply Like 5