Gel coat and Epoxy if done correctly will it work?

Talk Composites - The Forum for Advanced Composites

Back

Home
»
Advanced Composites Forum
»
Mould Making
»
Gel coat and Epoxy if done correctly will it work?

Gel coat and Epoxy if done correctly will it work?

Gel coat and Epoxy if done correctly will it work?

Author	Message
fastboats	fastboats posted 10 Years Ago HOT Topic Details
Group: Forum Members Posts: 9, Visits: 94	Looking to make a mold of a small performance boat hull. I have read that in order to make a very good mold that will last a long time some use carbon fiber vs fiberglass mat in a unimold type setup. Once the part is setup and flanges in place can I apply gel wait for that to tack and apply a layor of carbon down and expoy coat over that? Or will the Gel delaminate from the mold? Thanks for any help and please go easy I'm new and learning as much as I can. Edited 10 Years Ago by fastboats
	Reply Like 3
Reply
fastboats	fastboats posted 10 Years Ago HOT Post Details
Group: Forum Members Posts: 9, Visits: 94	OK so the heat generated would be the problem with more then a few layers of epoxy on a half layup mold? What's the reason why you can't use csm with epoxy?
	Reply Like 2

GO

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Threaded View

Gel coat and Epoxy if done correctly will it work?

fastboats - 10 Years Ago

you use carbon same as glass fibers. in poly resin watch for wax contamination on surface, it...

wojtepanik - 10 Years Ago

Are you talking about "mixing" Unimould Gel-coat with epoxy for backing?? That will probably not...

Dravis - 10 Years Ago

I'm not certain that it wouldn't work... I've used epoxy tooling gelcoat and backed it up with vinyl...

Hanaldo - 10 Years Ago

Yes, but I think that has to do with what will bond to what, and in which "state" Both Polyester...

Dravis - 10 Years Ago

Yeh that is my one doubt... But I'm not so sure that wax additive would be a bad solution. Once...

Hanaldo - 10 Years Ago

OK I found GC50 clear but I want black can I add color somehow? Add a pigment or spray clear and...

fastboats - 10 Years Ago

Edited.

fastboats - 10 Years Ago

sorry to thread jack, but if im reading this right. You can use epoxy gelcoat and follow up with VE...

kidpaint - 10 Years Ago

Correct. Just watch for styrene attack. If the epoxy isn't sufficiently cured, the styrene can...

Hanaldo - 10 Years Ago

I am curious why the original poster want to use epoxy resins. I have not used the specific Uni...

Fasta - 10 Years Ago

So I could get some gc50 color it as I want then apply to a surface (mold release applied first)...

fastboats - 10 Years Ago

In my experience the first and main thing that makes or defines the mould is the surface quality...

Fasta - 10 Years Ago

OK I'm sorry I missed a post. I'm looking to make a long lasting mold. I was reading that the non...

fastboats - 10 Years Ago

The uni mold like many others is a no shrink system. It should be good. (note I have not...

Fasta - 10 Years Ago

I understand what your saying for the most part. And thanks for the information. One thing I don't...

fastboats - 10 Years Ago

Because it's not good practice to lay all your reinforcement in one hit, like you can do with rapid...

Hanaldo - 10 Years Ago

OK so the heat generated would be the problem with more then a few layers of epoxy on a half layup...

fastboats - 10 Years Ago

OK I searched the csm and now understand it the binding agent that causes problems with epoxy.

fastboats - 10 Years Ago

Using epoxy wont create excessive heat with just 4-5mm thick. Using CSM builds thick laminates...

Fasta - 10 Years Ago

Similar Topics

Post Quoted Reply

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google

Explore

Messages

Mentions

Search