Bubbles in Xencast


Bubbles in Xencast
View
Options
Author
Message
moeggesit
m
moeggesit
posted 6 Years Ago HOT
Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)Forum Member (47 reputation)
Group: Forum Members
Posts: 4, Visits: 9
Hi, How can I avoid bubbles in the castings when using Xencast (currently general purpose)? The mould is dry but there are always bubbles present, often on the surface ruining the castings.
Many Thanks
Reply Like 5
Reply
Jimmyb
J
Jimmyb
posted 5 Years Ago HOT
Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)Junior Member (20 reputation)
Group: Forum Members
Posts: 2, Visits: 4
 
Warren (Staff) - 8/21/2020 9:45:26 AM
The shelf life of the P6 is 6 months so at 2 years old, age of the product could almost certainly be the issue. 


Warren, many thanks, looks like its time to buy a fresh batch. 
P.S.  I there  a date  best before or similar on the package, i don't seem to be able to locate one.
Reply Like 4
GO

Merge Selected

Merge into selected topic...



Merge into merge target...



Merge into a specific topic ID...



Submit

Threaded View
Threaded View
Bubbles in Xencast
moeggesit - 6 Years Ago
     It depends on the cause. Humidity can cause the P2 to have bubbles in as can low temperatures. Be sure to have thoroughly mixed the sediment into the mixture before using the resin and also giving it...
Warren (Staff) - 6 Years Ago
             Warren, Thank you, what is considered low temperature and what would be the ideal temperature? Is there another fairly ridged resin that would give a better finish/ consistency and a opaque...
moeggesit - 6 Years Ago
     Just to check, is this Xencast P2 or P6?
Rich (Staff) - 6 Years Ago
             Rich, It is P2 and otherwise perfect for the application. I don't actually mind which one as long as it does not have bubbles in it! Is there normally bubbles present in the P2 or is it a defect...
moeggesit - 6 Years Ago
     I would say 15C or below is low. Ideally 20C is the ballpark for most resins to perform at their best. It is unusual for their to be a lot of bubbles in the P2 resin system , hence Rich asking if yo...
Warren (Staff) - 6 Years Ago
             Everything is done at an ambient of approx. 20C using dry plastic containers so there should not be any moisture. It's stirred to avoid ingress of bubbles. Would it help to warm it up before or durin...
moeggesit - 6 Years Ago
     Sometimes this time of year, condensation cure moulds can end up with a bit of moisture in them. If warmed up to room temperature then they should not be a problem.
Warren (Staff) - 6 Years Ago
     Hi I am having problems with bubbles in my Xencast P6 castings. I read through the forum for answers first, and can confirm that the temperature and humidity would seem normal, as I am doing the...
Jimmyb - 5 Years Ago
     The shelf life of the P6 is 6 months so at 2 years old, age of the product could almost certainly be the issue.
Warren (Staff) - 5 Years Ago
             Warren, many thanks, looks like its time to buy a fresh batch. P.S. I there a date best before or similar on the package, i don't seem to be able to locate one.
Jimmyb - 5 Years Ago
     We can trace an exact expiry date through the batch number but for this resin it is 6 months from date of manufacture which, due to us having very short turnaround times means you can assume 6 months...
Warren (Staff) - 5 Years Ago

Similar Topics

Post Quoted Reply
Reading This Topic

Powered by InstantForum 2017-0 Final © 2025
Execution: 0.000. 3 queries. Compression Enabled.
Explore
Messages
Mentions
Search