Looking for help and info pls

Talk Composites - The Forum for Advanced Composites

Back

Looking for help and info pls

Author	Message
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	What do u mean by cutting into smaller peices Would that be on the second layer and so on ?
	Reply Like 3
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	I have tryed here as per above post waiting till tack I'll see how that gose or infusion as u say fasta But I am not sure how to do that Attachments IMG_4529.JPG (313 views, 726.00 KB)
	Reply Like 3
scottracing	scottracing posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 460, Visits: 5.2K	You need to cut the pieces smaller so that they sit into the tight rads. When you do wet lay like this you really need to force the fabric into the corners as it will bridge very easily with a 2x2 weave. Are you placing the whole mould in a vac bag? If you are as people have mentioned dont pull full vac initially. You need to make a bagging dibber esentislly a spatula to force the material and bagbinto the corners. Also ensure the vac bag has excess in the corners as it will bridge and pull the carbon up.
	Reply Like 2
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	Nearly got it talk a. About a had part to do Attachments IMG_4529.JPG (366 views, 726.00 KB)
	Reply Like 3
scottracing	scottracing posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 460, Visits: 5.2K	You will be better cutting strips with a 45degree orientation and laying them into the rads then putting an allover ply on.
	Reply Like 3
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	Hopefully I can get it Thanks
	Reply Like 10
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	The problem I am getting really is full vacuum I can here a leak but no matter what I can't seem to fix the leak
	Reply Like 3
Fasta	Fasta posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 468, Visits: 3.5K	If I were laying this part up in any process I would cut small clean rectangles to cover the vent sections only and then cut two larger longer lengths and lay this on each long side overlapping the whole centre vent sections. Clean joins are not very noticeable and usually much less noticeable than distorted weave. I can't see how you can get a leak on such a simple bag. Full envelope bag? Tape each end. Fastacraft Facebook page
	Reply Like 3
Coxo	Coxo posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 39, Visits: 476	Yeh fasta full envelope bag tape on each end
	Reply Like 3
MarkMK	MarkMK posted 8 Years Ago HOT Post Details
Group: Forum Members Posts: 338, Visits: 2K	Coxo (12/01/2017) What do u mean by cutting into smaller pieces Would that be on the second layer and so on ? I meant possibly trying to cut each of the inner 'up and down' sections of the piece as separate pieces that overlap each other slightly and then doing the outer flange section also as a separate piece with some small cuts so that you could overlap it onto the pieces already laid. Done neatly, the joins could be almost seamless and this would allow you to get the weave of each section nice and straight and in a uniform direction. It would also help with getting the surface layer tight into the mould without the risk of bridging. I'd also look to do something similar with the heavier backing layer, but you could afford to be a bit less exact with that as you'd only be trying to get it to lay down fairly tight onto the surface layer It'd be fiddly on a relatively small mould such as that, but misting the fabric with spray-tack or, perhaps, using something like EC's Profinish will help keep your cut lines sharp Done as a single surface layer it looks nigh-on impossible to achieve a neat looking finish
	Reply Like 2