Project Showroom

Talk Composites - The Forum for Advanced Composites

Back

Project Showroom

Author	Message
Warren (Staff)	Warren (Staff) posted 3 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Those parts are looking good. Much lighter than the originals? Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 3
Legoman	Legoman posted 3 Years Ago HOT Post Details
Group: Forum Members Posts: 29, Visits: 622	GSX-R 600 lower fairing. Vacuum Infusion.
	Reply Like 5
Warren (Staff)	Warren (Staff) posted 4 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Looks pretty good and the honeycomb pattern fabric is pretty rare these days. Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 2
Ken Olson	Ken Olson posted 4 Years Ago HOT Post Details
Group: Forum Members Posts: 8, Visits: 41	Here is a model boat I did with some red kevlar/carbon fabric. Turned out pretty good. Resin infused with 5.7 oz carbon, 2mm soric core and then this honeycomb on the outside.
	Reply Like 5
Richard webb	R Richard webb posted 5 Years Ago HOT Post Details
R Group: Forum Members Posts: 1, Visits: 25	+x Classicarbon - 9/21/2020 2:07:59 PM VW engine lid. Infiusion. Nice, I have made a VW engine lid to Edited 5 Years Ago by Richard webb
	Reply Like 4
Hanaldo	Hanaldo posted 5 Years Ago HOT Post Details
Group: Forum Members Posts: 2.5K, Visits: 28K	Nice job, a lot of work in that and it turned out really nice. Thats a hell of a chain!
	Reply Like 3
Coldever	C Coldever posted 5 Years Ago HOT Post Details
C Group: Forum Members Posts: 12, Visits: 187	I finished my carbon recumbent bike this summer. Made a set of molds from cnc-machined plugs. Frame was wet laminated under vacuum in two halves then joined. Stem and various other smaller carbon parts were made with the help of 3d-printed molds and cores. P8200026-2pieni by Mikko Hörkkö, on Flickr PA270178-2 by Mikko Hörkkö, on Flickr Edited 5 Years Ago by Coldever
	Reply Like 4
Classicarbon	C Classicarbon posted 5 Years Ago HOT Post Details
C Group: Forum Members Posts: 86, Visits: 639	VW engine lid. Infiusion.
	Reply Like 9
bennyT	b bennyT posted 5 Years Ago HOT Post Details
b Group: Forum Members Posts: 11, Visits: 777	+x andygtt - 8/18/2020 3:11:19 PM I made a new design of dash recently for my car (noble M12)... started as little more that filler and cardboard so shows what can be done with a cheap and dirty buck (if your quick and careful). Ive included pictures of the final product (some of them before they had been flatted and final lacquered), but also some buck pictures so people can see how the shapes were created, maybe give some motivation for those that think it takes more skills than it actually does. here is an original noble dash for comparison Looking really nice. Which method did you use for the carbon part i.e wet layup, infusion etc?
	Reply Like 4
Warren (Staff)	Warren (Staff) posted 5 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Brilliant work as usual Andy! You got the V weave very nicely done. Massive improvement over the original and also bet its much lighter too! Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 5