Mould for a Louver Panel

Talk Composites - The Forum for Advanced Composites

Back

Mould for a Louver Panel

Author	Message
Warren (Staff)	Warren (Staff) posted 3 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Updated the link above for you. You can also find it here: Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant Edited 3 Years Ago by Warren (Staff)
	Reply Like 4
k.alan.bates	k k.alan.bates posted 3 Years Ago HOT Post Details
k Group: Forum Members Posts: 36, Visits: 664	+x Warren (Staff) - 5/14/2020 1:50:24 PM That "forged" carbon effect has come out well. Depending on how the vents are cut, you can usually make it all as a one piece mould as well. We did a pair of similar vent moulds using our high temperature putty for OOA pre-preg. You can see the video tutorial here: Hand Laminating a High Temperature Mould Is there an updated link to that "Hand Laminating a High Temperature Mould" video? It currently takes me to a 404 page.
	Reply Like 5
Warren (Staff)	Warren (Staff) posted 5 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	That "forged" carbon effect has come out well. Depending on how the vents are cut, you can usually make it all as a one piece mould as well. We did a pair of similar vent moulds using our high temperature putty for OOA pre-preg. You can see the video tutorial here: Hand Laminating a High Temperature Mould Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant Edited 3 Years Ago by Warren (Staff)
	Reply Like 5
Hanaldo	Hanaldo posted 5 Years Ago HOT Post Details
Group: Forum Members Posts: 2.5K, Visits: 28K	Yeh for some components there is really no shortcut to the amount of trimming you will have to do.
	Reply Like 6
Steve Broad	Steve Broad posted 5 Years Ago HOT Post Details
Group: Forum Members Posts: 408, Visits: 4.1K	My vent mould .
	Reply Like 5
beliblisk	b beliblisk posted 5 Years Ago HOT Post Details
b Group: Forum Members Posts: 53, Visits: 2.8K	I made something similar for e46 m3 gtr vents. Making CF part is simple but the finishing is a bit frustrating......a lot of precision cutting and triming (one wrong move and you can bin the part). Edited 5 Years Ago by beliblisk
	Reply Like 5
Warren (Staff)	Warren (Staff) posted 5 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	When you make the pattern, you will need to block the vents, mould off it thus giving a mould with no vent holes in it. You create the vent holes when you lay up the fabric. In simple terms you do not lay fabric over the vent hole areas except around the very edge so you have something to trim. You want a small bit to trim as no matter how neat you are, the carbon raw edge is always a bit rough. Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 5
k.alan.bates	k k.alan.bates posted 5 Years Ago HOT Post Details
k Group: Forum Members Posts: 36, Visits: 664	+x Warren (Staff) - 5/13/2020 11:58:30 AM Generally speaking, your mould would be made as a solid closed vent item. In terms of lay up, you will need some overlap to give neat edges to trim back to. If you use pre-preg or a stabilised fabric like our ProFinish carbon cloth, you can cut the edges quite cleanly so you would only need an overlap of a mm or so to give something to sand smooth against. So that sounds like "solid closed vent item" means "making a solid transition then cutting out the opening." Is my interpretation correct and does that mean my initial thought is the best way to go? ...Follow up about your use of the word 'overlap': Are you 1) referring only to the layup technique and are calling for a 1mm overlap of prepreg material or 2) are you referring to a ~1mm return molded into the louver vents to allow the trim to marry up with the backside of the vanes rather than the leading edge? Thank you very much for your assistance.
	Reply Like 5
Warren (Staff)	Warren (Staff) posted 5 Years Ago HOT Post Details
Group: Administrators Posts: 2.5K, Visits: 8.5K	Generally speaking, your mould would be made as a solid closed vent item. In terms of lay up, you will need some overlap to give neat edges to trim back to. If you use pre-preg or a stabilised fabric like our ProFinish carbon cloth, you can cut the edges quite cleanly so you would only need an overlap of a mm or so to give something to sand smooth against. Warren Penalver Easy Composites / Carbon Mods - Technical Support Assistant
	Reply Like 5
k.alan.bates	k k.alan.bates posted 5 Years Ago HOT Topic Details
k Group: Forum Members Posts: 36, Visits: 664	I'm having a bit of a hard time conceptualizing how I would go about creating a mould for making a one-piece carbon fiber louver panel such as the one I have pictured. The flange around the perimeter is easy enough, but I can't quite reason how I would work out the open transition between the vane edges without making a solid transition then cutting out the opening. Does anyone have a better idea for handling the louver vanes in a way that wouldn't require cutting out large pieces of the part during postprocess? ...has anyone made composite louvers before? What was your mold process? Thanks everybody.
	Reply Like 5