Talk Composites - The Forum for Advanced Composites
Back
Login
Register
Login
Register
Home
»
Advanced Composites Forum
»
Mould Making
»
Can You Make A Two Part Mould Using Putty?
Can You Make A Two Part Mould Using Putty?
Post Reply
Like
2
Can You Make A Two Part Mould Using Putty?
View
Flat Ascending
Flat Descending
Threaded
Options
Subscribe to topic
Print This Topic
Goto Topics Forum
Author
Message
akitcarowner
akitcarowner
posted 9 Years Ago
ANSWER
HOT
Topic Details
Group: Forum Members
Posts: 4,
Visits: 35
Looking at doing a wheel center cap (Long story short, car stolen recovered and many things missing inc wheel center caps, so why not make them?) whilst a small part will need to be done in a two part mould (due to curves).
So can the putty be used or just stick with csm to make it?
The next question is of course, using wet lay-up and vacuum will that force the carbon into the curves without distorting too much?
I don't mind running a thin bead of black gel around edges to tidy up and then just put a circle at the bottom, thin bead, then use another piece of carbon for the edge?
These:
http://www.comp.co.uk/products/product.asp?item=chrome-plastic-2-5-cap-x4-2-3
Reply
Like
2
Hanaldo
Hanaldo
posted 9 Years Ago
ANSWER
HOT
Post Details
Group: Forum Members
Posts: 2.5K,
Visits: 28K
I don't see why the putty couldn't be used. It's really just a different type of reinforcement, so that doesn't mean it isn't suitable for the same processes. I'd say it is absolutely fine for multi-piece moulds.
I think those pieces could be a bit tight and tricky to wet-lay neatly, but then I've never been superb at wet-lay. I wouldn't hesitate to infuse them, so I'm sure they can be wet-laid successfully.
Reply
Like
3
Zebra
Zebra
posted 9 Years Ago
ANSWER
HOT
Post Details
Group: Forum Members
Posts: 14,
Visits: 32
I use epoxy putty to make two piece molds. It works exceptionally well for what I do. I prefer it to fiberglass any day.
A few things to consider:
It's not amazing at capturing fine detail.
You might need to do some small touch ups on the surface if you don't press it into the pattern in every spot.
The is a much higher chance of the part sticking. Epoxy sticks to epoxy very well. I wet the cf fabric and let it partially cure before laying it in the mold (for the first layer only). It adheres less when partially cured. The flip side to this is that, because it sticks so well, you might not even need to bother with a vacuum for simple parts.
Make sure the epoxy putty is not too thin in any area of the mold or it will snap when you demold. Make sure the edges in particular are thick (like one inch or so)
Make sure the pattern is smooth before using the epoxy putty. If it is textured the putty will stick no matter what mold release you use.
Add at least a one inch putty border around the edge of the mold so when you separate the two halves with a screw driver, the chips in the surface won't be in the mold cavity
Vaseline is typically enough to allow the mold halves to be seperated.
The putty I use is light and porous. Make sure you seal the surface with something before use. Vaseline is fine for a single use mold. Use something better if it is for multiple parts.
Reply
Like
3
GO
Merge Selected
Merge into selected topic...
Merge into merge target...
Merge into a specific topic ID...
Open Merge
Post Reply
Like
2
Similar Topics
Post Quoted Reply
Reading This Topic
Login
Login
Remember Me
Reset Password
Resend Validation Email
Login
Facebook
Google
Explore
Messages
Mentions
Search