Some questions on my first resin infusion..!

Talk Composites - The Forum for Advanced Composites

Back

Some questions on my first resin infusion..!

Author	Message
baja_patient	baja_patient posted 13 Years Ago HOT Topic Details
Group: Forum Members Posts: 135, Visits: 1.6K	Hi all, I have been working on a project for a fair while now, and I'm starting to see light at the end of the tunnel. As you can see in the attached pictures I started out with an unflanged mould in sight of using a wet lay-up technique. Due to wanting cosmetically perfect parts and after consultation from the EC staff I decided to go for resin infusion instead. I modified my moulds so there would be sufficient flange space by adding a frame and a high-gloss surface to ensure that I can pull 100% vac. I am just about ready to start my first infusion and would like a few tips. The first mould I want to do is 70x40cm and approx. 7cm deep at its deepest point. I am planning to use 2 layers 200g carbon cloth and 2 layers of approx 150g e-glass. Is this a good combination and how much IN2 resin will I need based on the information? There is breather material included in my starter pack and it is also mentioned in the instructions, yet not in the video. I assume I should be using it. One more question (i hope): Can the reinforcement be cut smaller than the edge of the mould, or does it have to be almost at the gum tape? I hope I've formulated myself correctly! Thanks alot. Fabian
	Reply Like 11
Reply
Joe	Joe posted 13 Years Ago HOT Post Details
Group: Forum Members Posts: 310, Visits: 1.5K	Hi, If your leak is too little to be noticed, what about wraping the whole mold in the vacuum bag? Then even if your mold has tiny cracks, the bag will enclose them. If you do so, be careful with sharp edges on your mold that could damage the bag. Good luck ! A $1000 electronic device will always protect a 10 cents fuse
	Reply Like 10

Merge into selected topic...

Merge into merge target...

Merge into a specific topic ID...

Threaded View

Some questions on my first resin infusion..!

baja_patient - 13 Years Ago

Hi, When all your fabric is cut to size, you need to weight it. Then, ideally, you would want 40%...

Joe - 13 Years Ago

Thanks alot Joe! It does help indeed. I am fairly new to infusion and still learning everything I...

baja_patient - 13 Years Ago

Honestly, I have no clue how much more resin you should mix. I really think it depends on your...

Joe - 13 Years Ago

So, first things first, Easycomposites makes everything look so easy lol!!! Great instructions,...

baja_patient - 13 Years Ago

Hi Baja, I'm not a composite expert at all, but i notice that you gum tape is not directly...

SebRS - 13 Years Ago

[quote][b]SebRS (04/05/2012)[/b][hr]Hi Baja, I'm not a composite expert at all, but i notice that...

baja_patient - 13 Years Ago

Hi, If your leak is too little to be noticed, what about wraping the whole mold in the vacuum bag?...

Joe - 13 Years Ago

Use this Guide to resin usage to work out how much you need to infuse.

Warren - 13 Years Ago

Thanks for the tips so far. Status update. I managed the infusion, didnt come out quite as expected...

baja_patient - 13 Years Ago

Just slow things down a bit in future. Leave the clamp loosely on the resin feed so you can nip it...

Warren - 13 Years Ago

Reading This Topic

Login
Remember Me Reset Password Resend Validation Email Login	Facebook Google

Some questions on my first resin infusion..!

Some questions on my first resin infusion..!

Merge Selected

Threaded View

Similar Topics

Reading This Topic

Login

Explore

Messages

Mentions

Search